众富购彩

山东山汽工程机器(团体)无限公司
热线德律风:400-879-1999 山汽官方微信
慎重申明 购机 售后
热线德律风:400-879-1999
您此刻地点的地位: 众富购彩官网> 消息资讯 > 行业消息 >

小型混凝土搅拌机刹车片的改换和平常颐养!

所属分类:行业消息 宣布时候:2020-08-17 来历:众富购彩:http://vncarmart.net 阅读量:18

  刹车片对车主来讲很是主要,保障了行驶中的宁静驾驶。普通来讲,刹车片应具备4大根基请求:
  The brake pad is very important for the car owner to ensure the safety of driving. Generally speaking, the brake pad should have four basic requirements:
  1.搅拌机适合的磨擦系数。磨擦系数是磨擦资料的根基参数,决议根基的刹车片制能源矩。国标就严酷请求制作商在包装上说明磨擦系数。磨擦系数恰当,太高会形成制动进程中的车轮抱死、标的目的失控和烧片,太低则制动间隔太长。
  1. Suitable friction coefficient of mixer. Friction coefficient is the basic parameter of friction material, which determines the basic braking torque of brake pad. The national standard strictly requires the manufacturer to indicate the friction coefficient on the package. If the friction coefficient is appropriate, too high will cause wheel lock, direction out of control and burning during braking; if the friction coefficient is too low, the braking distance will be too long.
  2.公道的小型搅拌机寿命。利用寿命是大师遍及存眷的产物目标。凡是刹车片能保障3万千米的利用寿命。像刹车片资料中接纳的大颗粒石墨和黄铜还可以或许削减对刹车盘的磨损。
  2. Reasonable service life of small mixer. The service life is the product index that everybody pays close attention to. Generally, the brake pads can guarantee a service life of 30000 km. For example, the large grain graphite and brass used in brake pad materials can also reduce the wear on the brake disc.
  3.搅拌机刹车片在制动时会发生刹时的低温,特别在高速行驶或告急制动时。在低温状况下,磨擦片的磨擦系数会降落,称为热阑珊性。热阑珊性的凹凸决议低温状况和告急制动。
  3. The brake pad of mixer will produce instantaneous high temperature when braking, especially when driving at high speed or emergency braking. At high temperature, the friction coefficient of friction plate will decrease, which is called thermal degradation. High temperature state and emergency braking are determined by the degree of thermal degradation.
                全主动上料搅拌机
  小型混凝土搅拌机的保护:
  Maintenance of small concrete mixer:
  1.在ATF油中放入一张#600砂纸,浸泡约30分钟。谨慎地敲打阀体,使卡住的阀杆从腔孔中零落。能够须要用小螺丝刀将其撬出。
  Soak in oil for about 1 minute. Carefully tap the valve body to remove the stuck stem from the bore. It may be necessary to lever it out with a small screwdriver.
  2.利用螺丝刀时,谨慎不要刮伤阀孔。查抄单向阀杆上是不是有磨擦陈迹。用浸有ATF油的#600砂纸打磨气门杆上的毛刺,而后用溶剂洗濯气门杆并用紧缩氛围吹干。
  2. When using the screw driver, be careful not to scratch the valve hole. Check for friction marks on the one-way stem. Grind the burrs on the valve stem with ? 600 sandpaper soaked in ATF oil, then clean the valve stem with solvent and dry it with compressed air.
  3.卷起渗透ATF油的#600砂纸的一半,并将其拔出卡住的气门杆的气门孔中。悄悄拧松砂纸并将其牢牢地贴在阀孔外表上,而后边推边拉边拧砂纸研磨阀孔。拔出600砂纸。
  3. Roll up half of the ? 600 sandpaper soaked in ATF oil and insert it into the valve hole of the stuck valve stem. Gently loosen the sandpaper and stick it tightly on the surface of the valve hole, and then screw the sandpaper to grind the valve hole while pushing and pulling. Pull out 600 sandpaper.
  4.用溶剂洗濯全部阀体,而后用紧缩氛围吹干。在气门杆外表涂抹ATF油并将其滴入气门孔。阀杆应能以本身分量落入阀孔底部。不然,反复步骤4偏从头测试。若是阀杆依然卡住,则改换阀体。
  4. Clean the whole valve body with solvent and then dry it with compressed air. Coat the surface of the valve stem with ATF oil and drip it into the valve bore. The valve stem shall be able to fall into the bottom of the valve bore with its own weight. Otherwise, repeat step 4 and retest. If the stem is still stuck, replace the valve body.
  5.掏出小型混凝土搅拌机的阀杆,用溶剂洗濯阀杆和阀体。用紧缩氛围吹干一切整机,而后用ATF油作为光滑剂从头拆卸。
  5. Take out the valve rod of small concrete mixer and clean the valve stem and valve body with solvent. Dry all parts with compressed air and reassemble with ATF oil as lubricant.
  6.倡议对混凝土储罐及收支口四周停止洗濯,确保混凝土不结块。
  6. It is suggested to clean the concrete storage tank and the surrounding of the inlet and outlet to ensure that the concrete does not agglomerate.

 

众富购彩官网 产物 德律风 置顶
云彩店 七星乐官网 QQ爱彩 178彩票网 十大正规平台 500vip