众富购彩

山东山汽工程机器(团体)无限公司
热线德律风:400-879-1999 山汽官方微信
慎重申明 购机 售后
热线德律风:400-879-1999
您此刻地点的地位: 众富购彩官网> 消息资讯 > 行业消息 >

主动上料搅拌机施工的各部位操纵

所属分类:行业消息 宣布时候:2021-02-26 来历:众富购彩:http://vncarmart.net 阅读量:18

1.搅拌车搅拌筒的扭转由液压马达经由过程公用行星加速机动员,行星加速机的输入轴能够或许完成必然角度的摆动,以知足卑劣路况下搅拌筒的跳动。
1. The rotation of the mixer drum is driven by the hydraulic motor through a special planetary reducer. The output shaft of the planetary reducer can realize a certain angle swing to meet the beating of the mixer drum under bad road conditions.
2.液压体系接纳恒功率变量柱塞泵,削减发念头的功率消耗。
2. Constant power variable piston pump is used in the hydraulic system to reduce the power loss of the engine.
3.进水体系可根据计量设定完成主动进水。
3. The water inlet system can automatically feed water according to the metering setting.
4.干料上料,根据设想好的配比由铲臂、动臂缸、定量的料斗主动上料。
4. Dry material feeding: according to the designed proportion, it is automatically fed by shovel arm, boom cylinder and quantitative hopper.
主动上料搅拌机
5.主动上料搅拌车搅拌筒内壁上设置双螺旋形叶片,正向扭转为进料、混凝土搅拌;反向扭转,在螺旋叶片的鞭策下、混凝土由出料口出料。
5. Double spiral blades are set on the inner wall of the mixing drum of the automatic feeding mixer, which rotate in the positive direction for feeding and concrete mixing; in the reverse direction, the concrete is discharged from the discharge port under the push of the spiral blades.
6.行走体系由发念头经由过程液力变矩器、前后传动轴到前后桥。本发现接纳前后双桥驱动情势。接纳液力变矩器削减对发念头的打击、耽误了发念头的寿命。
6. The traveling system is composed of engine, front and rear transmission shafts and front and rear axles. The invention adopts a front and rear double axle driving form. The hydraulic torque converter is used to reduce the impact on the engine and prolong the service life of the engine.
换油:搅拌机普通每半年必要改换一次光滑油,光滑油的型号为32#机器油,换油时,谨慎拧开油塞,放进其内存油,注重油枪内能够会有残剩的内压,以防油的放射。
Oil change: generally, the blender needs to change the lubricating oil every six months. The type of lubricating oil is 32 # machine oil. When changing the oil, carefully open the oil plug and put the oil in the blender. Pay attention to the residual internal pressure in the oil gun to prevent the oil from spraying.
轴承光滑脂:普通大修时改换一次,光滑脂量为轴承腔空隙1/3-1/2,光滑脂保举接纳低温钙纳基光滑脂。
Bearing grease: it should be replaced once in general overhaul, and the amount of grease should be 1 / 3-1 / 2 of the bearing cavity clearance. High temperature calcium base grease is recommended.
搅拌机的泄漏掩护处置:假设渗漏开关掩护,表现机电侧的机器密封破坏,必必要查抄和补缀,翻开油室腔的梗塞,排尽其内积液。
Leakage protection treatment of mixer: if the leakage switch is protected, it means that the mechanical seal on the motor side is damaged. It must be checked and repaired. Open the blockage in the oil chamber and drain the liquid in it.

 

众富购彩官网 产物 德律风 置顶
云彩店 七星乐官网 QQ爱彩 178彩票网 十大正规平台 500vip